Showing posts with label Grey Roots Museum & Archives. Show all posts
Showing posts with label Grey Roots Museum & Archives. Show all posts

24 September 2015

HUMIDITY, IT’S ALL-RELATIVE: HUMIDIFICATION TREATMENT OF A BIRCH BARK CANOE MODEL PART 2

CONSERVATION TIPS & TRICKS

BY: NIKITA JOHNSTON

Recap: This past July as Collections Conservation Intern at Grey Roots Museum & Archives I began treatment on a birch bark and quillwork model canoe for the I Made it Myself: Folk Art of Grey County exhibit to open November 21, 2015. I Made it Myself asks the question, what constitutes “folk art”. 

Donated by a prominent family from Owen Sound in the 1970s, the canoe model is a great example of First Nations influence on Canadian folk art, seen in the beautiful floral quillwork designs.

Canoe prior to treatment.
Johnston 2015

In Part 1 I discussed the construction of the humidification chamber and the initial stages of treatment including:
Step 1: Condition Report
Step 2: Spot Test
Step 3: Cleaning (both dry and wet)

I should note that cleaning the canoe took several days, partly because of the amount of ingrained dirt, and partly because of the delicate nature of the quillwork, which required very careful attention while cleaning. However, the results were spectacular, and highlight the importance of protecting objects from the damaging and aesthetically unpleasing effects of dust. Once the entire surface of the canoe was cleaned it was time to begin humidification.


Interior of the canoe Before Treatment.
Johnston 2015
Interior of the canoe After Treatment.
Johnston 2015

Step 4: Humidification

For the humidification of the canoe, I used sterile distilled water. I began first with the two bottom pieces, which had become separated from the rest of the hull, as these had no quillwork components and would give me a good idea of how long it would take to regain some flexibility in the bark to allow for reshaping.

The pieces were placed inside the chamber, on foam supports to avoid contact with any pooling water, and the pieces were placed away from the wall of the chamber to avoid condensation on the plastic. The ultrasonic humidifier was also placed on a support and in a plastic container within the chamber to contain any potential leaks and keep the electrical cord out of any pooling water.


Humidification Chamber with bottom hull sections of the canoe and internal foam supports.
Johnston 2015

Humidification took place over several days. Every few hours I would check the pieces to ensure that the bark was not becoming saturated and to see how the flexibility of the pieces was improving. After the first 24 hours I began adding additional foam support inside the pieces to help with the reshaping and provide support as the bark became more supple.

There was a noted improvement in the flexibility of the pieces, particularly towards the centre of the hull where the bark was the thinnest. However, the ends (bow and stern) showed little improvement.

The canoe was removed from the chamber when it was observed that a tiny amount of white mould had formed around one of the small incision holes. The canoe was allowed to achieve equilibrium with the relative humidity of the conservation lab, giving the mould a chance to dry out over 48 hours. The mould was then removed using a brush and vacuum.

The mould growth was likely caused by residual soiling in the hole, resulting from previous storage at the old museum site in an area where occasionally foodstuffs were produced. Observation continued for the next few weeks to ensure no additional mould growth occurred. It is recommended that the canoe undergo no further humidification to avoid the possibility of additional mould growth.

Since some headway had been made in reshaping the bottom pieces, the rest of the canoe was placed in the humidification chamber. Observation of these pieces occurred more frequently because of the quillwork. This was an important consideration as the hull was removed after only 48 hours in the chamber because it was observed that some of the quillwork pieces and cedar strappings had come loose in the higher humidity.


Lifting of the quillwork caused by high humidity in the humidification chamber.
Johnston 2015

Unfortunately, humidification did not achieve the desired results, which was to reshape the canoe hull to allow the separated pieces  to be re-attached. This is likely a result of the canoe sitting in storage for several decades without proper interior support, which resulted in the bark collapsing and curling inwards. Proper interior supports and a dust cover are two preventive conservation practices that could have lessened the resultant damage.

Step 5: Repairs

There were previous areas of loss or damage to the canoe that required some repair, as well as areas that had come loose in the humidification process. Neutral pH white PVA glue was used to re-attach lose components, as it is a stable and long lasting adhesive and is reversible.


Before Treatment of quillwork.
Johnston 2015
After treatment of quillwork using neutral pH white PVA glue.
Johnston 2015

Additional repairs required the sourcing of cotton cord, which was then colour matched to the remaining cordage on the canoe. This was then threaded through original holes at the bow and stern of the canoe to support the gunnels (or gunwales).


Colour matching cotton cord.
Johnston 2015

Step 6: Mounting

Once repairs were completed, I created two mounts for the canoe that would support the bottom pieces of the hull within the body of the canoe. Both mounts were made from gator board (a foam core board). One mount was made for storage and has a tray base in order to catch any pieces that come loose in the future. The second mount is more minimal for display purposes and was painted black with acrylic paint and allowed to off gas over 48 hours. When in storage a dust cover of neutral pH tissue will be used. The supports also allow the canoe to be handled and moved without touching the canoe itself.

Mounted canoe in storage mount with tray bottom.
Johnston 2015

Although it was disappointing that the humidification of the canoe did not allow for the re-attachment of the bottom pieces of the hull, the canoe received some much needed TLC and is now ready to be displayed to the public. With the removal of the surface soiling and the creation of a proper mount and internal supports the canoe can now be showcased, and will serve as an example of good collections care and management.

8 July 2015

HUMIDITY, IT’S ALL RELATIVE: HUMIDIFICATION TREATMENT OF A BIRCH BARK CANOE MODEL PART 1

CONSERVATION TIPS & TRICKS

BY: NIKITA JOHNSTON

For this post, instead of focusing on general tips and tricks, I thought I would showcase a specific object treatment that I am working on at Grey Roots Museum & Archives. This fall one of the upcoming exhibits will display a variety of folk art created in Grey County or brought to the county by local individuals. Pieces to be exhibited include: carvings, stitched samplers, hooked rugs and tramp art.

In preparation for this exhibit, I have been given the challenge of prepping several pieces of folk art for the exhibit. One of the pieces I will be working on in the coming weeks is a birch bark canoe model.

Johnston 2015

Donated by a prominent family from Owen Sound in the 1970s, this canoe is a great example of Canadian folk art. Models like this were popular as toys and handicrafts traded among Europeans. Models resembled canoes built by indigenous groups and used by explorers and fur traders in the woodland and sub-arctic regions of Canada. This example showcases additional First Nations influence in the beautiful floral quillwork designs across the sides of the canoe.

Johnston 2015

Unfortunately, this beautiful piece requires some extensive work before it can be exhibited. The canoe, which is in three main pieces, was acquired by the museum in its current condition. At some point in the past, two parts of the bottom hull became detached from the main body of the canoe. Little remains of the original thread used to attach these pieces to the body. As they were no longer held under tension the pieces of birch bark proceeded to curl, as they will do, particularly in low Relative Humidity environments such as we try to maintain in collection storage.

Johnston 2015

At this point, it would be impossible re-attach the hull pieces without damaging them, as they are far too rigid to bend back into shape. The solution therefore is to re-introduce moisture in a controlled way, so that these pieces can relax and be reshaped to better fit the canoe body without causing damage. Unfortunately, as is common in many small museums we do not have a commercial humidification chamber on hand, so this treatment requires me to be somewhat creative!

Source

That’s right ladies and gentlemen, I built myself a humidification chamber out of common materials around our lab, including: an archival quality textile storage box, polyethylene sheeting, double sided archival tape, cardboard tubes, polyethylene foam…and every handy man or woman’s favourite …duct tape. Oh, and of course my water source for raising the relative humidity of my humidification chamber, a small commercially available ultrasonic humidifier.

Johnston 2015

Of course, before beginning the humidification of the canoe pieces, which I will chronicle in Part 2, there are several necessary and essential steps in the treatment process.

Step 1: Condition Report

Before commencing any treatment it is important to document the condition of the piece, examining the object to be treated and describing its current condition in detail, including any damage, or evidence of previous treatment and repairs.

Johnston 2015
Step 2: Spot Test

Before placing the canoe into the humidification chamber, or performing any type of wet cleaning, it is important to test the paint used on the quills for colourfastness and solubility in water. This is a simple test involving distilled water and a cotton swab. The slightly dampened swab is gently rubbed on an indiscreet part of the painted quillwork to test for colourfastness.

Johnston 2015

If no paint comes away, we can assume it is safe for the humidification chamber. Each paint colour is tested in this way as some colours and dyes are more likely to degrade, or run than others. These are often referred to as fugitive dyes or colours. Lucky for me none of the paint colours appeared to be soluble in water. Yay!

Step 3: General Clean

Finally, before starting the humidification process, it is essential that a general cleaning of the surface be conducted. This is to ensure that any addition of moisture does not cause the surface dirt to penetrate into the birch bark causing irreversible staining. Cleaning also provides another opportunity to examine the piece in detail and note any areas of potential weakness.

Cleaning is done mechanically using soft brushes, a vacuum and sponges. If necessary, a wet cleaning may be performed using cotton swabs slightly dampened with distilled water. As birch bark is hygroscopic, and has the potential to warp with the addition or removal of moisture, a wet clean must be done carefully so as not to introduce more moisture than is necessary to remove the surface dirt.



Now that my initial steps are taken care of, it is time to begin the humidification treatment. The aim is to raise the general humidity without soaking the birch bark or quills, allowing the bark to relax and be reshaped without causing unnecessary damage. Humidification should never be hurried, nor taken to excess, and care must be taken in terms of monitoring for potential mould growth.


Source

Research has shown that previous humidification treatments of birch bark objects have taken up to several days, hence the reason for a two-part post.

Wish me luck for Part 2!